Battery Calculatorby Voltage Drop Calculator

Battery calculators / Runtime & backup

Understand your battery. Plan your power.

Standby and Alarm Battery Load Calculator

Estimate battery capacity for sequential standby and alarm operating periods.

Your inputs

A
h
A
min

Defaults are illustrative. Enter your battery or equipment data. Efficiency and usable capacity inputs are percentages.

Your result

Awaiting your inputs

Enter your values and press Calculate. Your result will appear here.

Explained formula · Sources listed below · No sign-up

The method

Formula and calculation steps

Required Ah = (standby A × standby hours + alarm A × alarm minutes ÷ 60) × multiplier

Enter complete battery-side current totals for each state, including the panel and all battery-powered devices. Alarm current is the total during alarm, not an increment above standby.

Illustrative defaults are not a compliance determination. Required times and factors depend on system type, locally adopted NFPA 72 edition, panel manual and authority having jurisdiction. Check approved battery and charger limits separately.

Fire alarm standby battery calculations and worksheets

A fire alarm battery calculation commonly separates standby and alarm operating states. Compute total battery-side standby current times standby hours and add total alarm current times alarm hours. Apply only a justified sizing multiplier and then check panel-approved battery and charger constraints.

Addressable and conventional fire alarm battery calculations can use different device current schedules even though the charge integration is the same. Access control and DC backup supplies also need state-specific loads. This generic worksheet takes current totals; it does not contain a library of detector, sounder or panel currents.

Worked example

A transparent starting point

(0.2 A × 24 h + 1 A × 5/60 h) × 1.2 = 5.86 Ah.

The values below are computed with the same formula as the calculator. They are examples, not manufacturer performance claims.

How one input changes the answer

Total standby current (A)Estimated required capacity
0.1 A2.98 Ah
0.2 A5.86 Ah
0.3 A8.74 Ah

All other inputs use the illustrative defaults in the form.

Fire alarm standby battery calculations and worksheets — calculated examples

Each row below is calculated from the stated case inputs. Inputs not changed in a row use the assumptions listed after the table.

CaseChanged inputsResult
0.1A standby, 5min alarmTotal standby current: 0.1 A; Required alarm duration: 5 min2.98 Ah
0.1A standby, 15min alarmTotal standby current: 0.1 A; Required alarm duration: 15 min3.18 Ah
0.2A standby, 5min alarmTotal standby current: 0.2 A; Required alarm duration: 5 min5.86 Ah
0.2A standby, 15min alarmTotal standby current: 0.2 A; Required alarm duration: 15 min6.06 Ah
0.5A standby, 5min alarmTotal standby current: 0.5 A; Required alarm duration: 5 min14.5 Ah
0.5A standby, 15min alarmTotal standby current: 0.5 A; Required alarm duration: 15 min14.7 Ah
1A standby, 5min alarmTotal standby current: 1 A; Required alarm duration: 5 min28.9 Ah
1A standby, 15min alarmTotal standby current: 1 A; Required alarm duration: 15 min29.1 Ah

Unchanged inputs: Total standby current = 0.2 A; Required standby duration = 24 h; Total current during alarm = 1 A; Required alarm duration = 5 min; User-specified sizing multiplier = 1.2 . Rows change only the listed inputs. Values are arithmetic examples, not manufacturer performance claims.

Common questions

Is this an official Fire-Lite, Notifier or C-TEC calculation?

No. Use the exact panel manual and manufacturer worksheet for approved device currents and required factors.

How should I use the result?

Illustrative defaults are not a compliance determination. Required times and factors depend on system type, locally adopted NFPA 72 edition, panel manual and authority having jurisdiction. Check approved battery and charger limits separately.

Is this an NFPA 72 battery calculation worksheet?

It is a generic standby/alarm charge worksheet. The required durations, correction factors and acceptance criteria must be checked against the locally adopted edition and the exact panel documentation; defaults are not a compliance finding.

Does it support Fire-Lite ES-50X, ES-200X, ES-1000X or MS-5UD?

It does not reproduce their manufacturer worksheets or device-current databases. Use the exact model manual to obtain approved currents, charger limits and calculation requirements, then enter justified totals here for an arithmetic check.

Can I use it for Notifier NFS-320, NFW-50X or NFW2-100?

Only as a generic arithmetic check using verified model data. This page is not the Notifier battery calculator software and cannot certify an approved battery combination.

Does it include Silent Knight 5208, 6700, 6808, 6820 or Potter AFC-1000 data?

No model-specific currents are supplied. Use the relevant manufacturer calculation sheet. A matching product name in a search does not make generic defaults appropriate.

Can I use C-TEC, Apollo or Altronix battery sizing data?

Enter verified total currents and justified durations from the exact system instructions. This tool does not retrieve or approve those manufacturers data.

How do I create a fire alarm battery calculation in Excel?

Create separate standby A×h and total alarm A×minutes/60 columns, add them and apply the documented multiplier. Keep device quantities and datasheet references in your worksheet; this page does not export an official form.

Sources and formula basis

Source addresses are shown as plain text. Algebraic rearrangements, example tables and user-selected loss factors are calculated on this site. A reference does not endorse every illustrative input.

  1. Maccor — C-rate in battery testinghttps://www.maccor.com/battery-testing-knowledge-center/fundamentals/understanding-c-rate-in-battery-testing.html
  2. NFPA 72 — National Fire Alarm and Signaling Code; verify the locally adopted edition and panel manualhttps://www.nfpa.org/codes-and-standards/nfpa-72-standard-development/72

Source pages checked: November 19, 2026. Verify current product data and locally adopted requirements before design or installation.