Battery Calculatorby Voltage Drop Calculator

Battery calculators / Runtime & backup

Understand your battery. Plan your power.

Battery Life by Amp Draw

Calculate constant-current DC runtime without assuming an inverter or an operating voltage.

Your inputs

Ah
A
%

Defaults are illustrative. Enter your battery or equipment data. Efficiency and usable capacity inputs are percentages.

Your result

Awaiting your inputs

Enter your values and press Calculate. Your result will appear here.

Explained formula · Sources listed below · No sign-up

The method

Formula and calculation steps

Runtime (h) = Ah × usable fraction ÷ current A

Amp-hours divided by amps gives hours. Because the input is already measured on the battery side, no conversion-efficiency factor is applied.

Use average battery-side current, including standby draw. Rated Ah may fall at high current, especially for lead-acid cells; use the Peukert tool when suitable.

Battery life with amp draw and car battery drain

Use this amp-hour run time calculator when the average battery-side current is known. A DC battery backup calculator expressed in amps avoids an unnecessary voltage assumption. If a meter measures input current before an inverter, conversion loss is already reflected in that reading; applying an extra inverter efficiency factor would count it twice.

For a car battery drain calculation, average parasitic current and the available starting reserve both matter. A battery can cease to start a vehicle well before its full rated Ah has been discharged. Choose a usable fraction that reflects the operating requirement rather than assuming every Ah is available for accessory use.

Worked example

A transparent starting point

100 Ah × 80% ÷ 5 A = 16 hours.

The values below are computed with the same formula as the calculator. They are examples, not manufacturer performance claims.

How one input changes the answer

Average battery-side current (A)Constant-current runtime
2.5 A32 hours
5 A16 hours
7.5 A10.66667 hours

All other inputs use the illustrative defaults in the form.

Battery life with amp draw and car battery drain — calculated examples

Each row below is calculated from the stated case inputs. Inputs not changed in a row use the assumptions listed after the table.

CaseChanged inputsResult
7Ah at 1ARated battery capacity: 7 Ah; Average battery-side current: 1 A5.6 hours
7Ah at 5ARated battery capacity: 7 Ah; Average battery-side current: 5 A1.12 hours
7Ah at 10ARated battery capacity: 7 Ah; Average battery-side current: 10 A0.56 hours
50Ah at 1ARated battery capacity: 50 Ah; Average battery-side current: 1 A40 hours
50Ah at 5ARated battery capacity: 50 Ah; Average battery-side current: 5 A8 hours
50Ah at 10ARated battery capacity: 50 Ah; Average battery-side current: 10 A4 hours
100Ah at 1ARated battery capacity: 100 Ah; Average battery-side current: 1 A80 hours
100Ah at 5ARated battery capacity: 100 Ah; Average battery-side current: 5 A16 hours
100Ah at 10ARated battery capacity: 100 Ah; Average battery-side current: 10 A8 hours
200Ah at 1ARated battery capacity: 200 Ah; Average battery-side current: 1 A160 hours
200Ah at 5ARated battery capacity: 200 Ah; Average battery-side current: 5 A32 hours
200Ah at 10ARated battery capacity: 200 Ah; Average battery-side current: 10 A16 hours

Unchanged inputs: Rated battery capacity = 100 Ah; Average battery-side current = 5 A; Usable capacity fraction = 80 %. Rows change only the listed inputs. Values are arithmetic examples, not manufacturer performance claims.

Common questions

Do I need voltage for this calculation?

No. Voltage is needed for energy in Wh, but it cancels in a constant-current amp-hour calculation.

How should I use the result?

Use average battery-side current, including standby draw. Rated Ah may fall at high current, especially for lead-acid cells; use the Peukert tool when suitable.

How do I calculate battery life with amp draw?

Multiply rated Ah by the usable fraction, then divide by average battery current in A. A 100 Ah battery with 80 Ah available lasts an ideal 16 hours at 5 A.

Can I use milliamps for a car battery draw calculator?

Convert mA to A first: 50 mA is 0.05 A. At that current, 1.2 Ah is removed in 24 hours. The resulting time is an ideal charge budget and does not promise that the vehicle will still start.

Does battery capacity in Ah equal the current I can draw?

No. Ah is a quantity of charge; maximum continuous or pulse current is a separate battery rating. An Ah-based runtime estimate cannot establish a safe discharge limit.

What if my load switches on and off?

Use its time-weighted average battery current or the duty-cycle calculator. Include the off-state current and any intermittent loads over the period being estimated.

Sources and formula basis

Source addresses are shown as plain text. Algebraic rearrangements, example tables and user-selected loss factors are calculated on this site. A reference does not endorse every illustrative input.

  1. Cadex Battery University BU-904 — capacity testing and reserve capacityhttps://www.batteryuniversity.com/article/bu-904-how-to-measure-capacity
  2. Maccor — C-rate in battery testinghttps://www.maccor.com/battery-testing-knowledge-center/fundamentals/understanding-c-rate-in-battery-testing.html

Source pages checked: November 19, 2026. Verify current product data and locally adopted requirements before design or installation.